van Gilder Tool Descriptions

Van Gilder Clay Tools

Click on the tools to see a detailed description of each, along with Bill's comments and tips for use.

		Roped Rollers Here is what Bill has to say: "There are lots of simple tools to use when decorating your work. And often, simple is best! These long and short roped dowels are easy to use and extremely effective. Held between your fingertips like a small rolling pin and using a steady, gentle hand pressure, roll a roped dowel across a soft clay tile in one direction. Turn the tile and roll again. Inlay thin cardboard as "resist." Using a roped dowel, roll over your design to create an interesting 3-D decoration. You can stamp into and over a roped texture, too. Use them to rope-texture a leather-hard pot; plate rims, handle surfaces, vase and cup forms. Use the large dowel for big pots, the small dowel for small ware. Try inlaying slip into the roped surface. Allow the form to dry until stiff leather-hard, scrape off the top slipped surface and over-glaze as a final step. Beautiful!" The small dowel is 3" long x 3/4" diameter. The large dowel is 5" long x 3/4" diameter. (back to top)

		Aluminum Wire Knife Here is what Bill has to say: "Designed to comfortably fit the hand, this lightweight and hard-surfaced aluminum "knife" will become one of your most-used studio tools - for handbuilding and at the wheel. Unlike a flat knife blade, the ultra-thin textured and tensioned wire cuts through clay without drag or distortion. It's ideal for cutting coils! And, it's a safe tool to use in the classroom. It's a great tool for leveling rims - a safe alternative to the more dangerous needle tool. Use it to trim teapot spouts and handle ends, facet, cut-out feet and more..." Size: 3" wire length in a 5" x 3/4" U-shaped frame (back to top)

		Edge Rounding Tool Every potter should have this sturdy, hardened-steel edge-rounding tool in their tool box! Use it when hand building to quickly round and smooth the sharp edge, or rim of a leather hard slab. One evenly pressured pull of the tool along a squared edge smoothly rounds the edge profile - an efficient replacement for the laborious 'rasp' tool typically used. Use it on slab plate and platter rims, the hand-built edges of vase forms — anywhere a smooth, rounded rim is desired. 'Adjust', or decrease the diameter of a leather hard, thrown lid by using the tool at the wheel to 'skim' away excess clay from a lid rim. Do it in one easy step to create a beautifully round-edged profile. (back to top)
		Undercut Tool Here is what Bill has to say: "This 3-in-1 hardwood throwing tool will quickly become your most useful and favorite tool at the wheel! You will save time as you pick up and put down fewer tools when working at the wheel. Use this tool to undercut a bevel at the foot of a thrown pot and then use the long beveled edges to rib your pot into shape. And use the pointed ends of the tool to groove design-lines around a form. Grooved surface keeps this tool from slipping from the fingertips and includes a hole for hanging up." 5" length x 1" width x 3/16" thickness with 2 x 45 degree beveled ends (back to top)

		Profiled Foot Rib Here is what Bill has to say: "Here's an alternative to trimming! Produce an instant rounded foot profile by pushing this easy-to-use tool into the base edge of a wet pot on the wheel. You can create an interesting scalloped foot profile by rhythmically pressuring the tool into the base edge of your slowly spinning form. Using the cornered point of the tool, add some decorative lines to complete your foot treatment. Pull it along the foot of a slab-based form to securely attach the wall to the base. And, at the same time, create an even, rounded, smooth foot edge - all in one step! Each tool has two rounded foot profiles and an easy-to-grip center hole. Made of hardwood." Size: 2" x 2-1/2" x 3/8" thickness (back to top)

		Hole Cutter Here is what Bill has to say: "The most efficient hole-cutting tool you'll ever use! The no-clog design makes hole-cutting quick and easy. Cut holes from 1/16" to 1/2" in diameter - with one tool. Extra-sharp blade edges cut through leather-hard clay cleanly, without excessive sanding to follow. Touch the tool point at the center of the hole to be cut. Add a slight pressure and twist to produce the perfect hole! Use the small end of the tapered handle to counter-sink and smooth hole edges. Cut hole patterns in colanders and sieves, garlic jars, potpourri pots, candle lamps, teapots and more..." Hardwood tapered handle is 2-1/2" in length, metal cutting blade is 2-3/4" in length (back to top)
		Textured Block Set Here is what Bill has to say: "Add an interesting texture to your coiled handles by rolling coils of clay between these two non-stick corrugated boards. Position the boards at different angles and directions to produce an assortment of great textures: linear cross-hatching, twisted spirals, circular rings, straight-line grooves, and more! The corrugated surfaces are sized to create textures in the correct proportion used for functional pottery. Decorate casserole handles, mug handles, handbuilt knobs, foot coils ... Your search for a sturdy corrugated texture tool is over! " Base board is 6" x 6" x 1/2" thickness; top board is 5" X 5" x 1/2" thickness Made of hardwood.
		(back to top)
		Butter Paddles You'll discover a myriad of uses for these traditional, hard-to-find kitchen tools. Add a fine texture to small handles by positioning the corrugated paddle surfaces face-to-face and rolling a small coil of clay between them. Alter the positions of the paddles to create squared and diamond-shaped, cross-hatched patterns, straight-line textures, wrap-around swirled patterns and more... Or, dip a single paddle into water and use it to slap the side of a wet thrown pot to create a random decoration. TIP: To create a random "slapped" texture on a rounded thrown pot, slap the wet form when it's in a cylinder shape. Then belly it out from the inside, into round. Made from hardwood & Sold in pairs. Paddles measure 8-1/2" L X 2" W X 3/16" thickness. (back to top)
		Wiggle Wire Here is what Bill has to say: "Add interest to the bottom surface of each pot you make! Pull and wiggle this sturdy corrugated wire tool beneath each form as you cut it from the wheelhead to create an assortment of subtle linear patterns. No more plain, boring base surfaces! Create great patterns across slabs and tiles. Use your wiggle wire to cut some freeform facets into your work, or cut and decorate the rims of bowls and plates. You’ll find unlimited possibilities for your wiggle wire! Helpful hint: When throwing pots intended to be wiggle-wired from the wheelhead or a bat, be sure to add 1/8" to the thickness of each pot base to compensate for a deeper corrugated cut." 16"L wire with two sturdy hardwood handles, 3/4" dia. x 2-1/4" L (back to top)
		Hump Cut-Off Tool Here is what Bill has to say: "This Asian-style cut-off tool is easy to use. After throwing a form at the top of a hump, use the beveled pointed end of the tool to cut a 1/2" angled groove below the foot. Then, reverse the position of the tool in your hand and, with the wheel spinning slowly, lay the end of the string into the corner of the groove. Like a toy top, allow the string to wrap around the foot and immediately pull the string from the clay. The string will neatly release the form from the hump with a perfectly level base cut." 6-1/2" L. x 1/2" hardwood with 8" string
		(back to top)
		Siphon Blower Here is what Bill has to say: "This is one of the most efficient glazing tools you'll ever use. This traditional Japanese oral spray tool is simple to use and only requires a gentle blowing from your mouth. You will broaden your decorating techniques repertoire as you build multiple slip and glaze surfaces onto your work. Spot spray or feather layers of glaze onto the shoulder of a pot, at the foot, or subtly highlight knobs and handles. Spray over glaze mistakes and unwanted finger marks. Spray slip or glaze over paper or cardboard silhouettes; or patch-spray an organized or random pattern across or around a pot. Rather than dip or pour glaze over that large pot, spray it! Use your water-filled spray-can to mist and dampen leather-hard works in progress. No more worn-out pump bottles to deal with! For extensive layered applications, have several spray cans loaded and on hand. Lightly pressure each can, in turn, onto your compressor nozzle to quickly change colors - without the hassle of constantly cleaning up spray guns and bottle containers! The no-clog design allows for hours of efficient spraying. These spray cans clean up easily by just rinsing under running water. Remember, if the glaze is too thick, you won’t be able to spray it. Thinner glazes work best, so you may need to apply more than one coat. These spray cans clean up easily by just rinsing under running water." Two sizes available: C-126-17 Large Siphon Blower 2-3/4" H x 6-3/4" L C-126-16 Small Siphon Blower 1-1/2" H x 6-3/4" L (back to top)